One pack, all three print lines. The Bear Transfers Sample Pack puts a real DTF transfer sheet, HyperColor 9-color prints and UV DTF 3D stickers in your hands — printed on the exact same film, inks and presses as full production orders. No mock-ups, no marketing samples: this is what your customers would wear.
What to do with it: press the DTF designs onto a tee or hoodie and feel the soft hand; stretch the print to see zero cracking; run it through the wash to test our 75+ wash durability. Compare the HyperColor prints side-by-side with standard CMYK — the neon oranges, electric blues and deep gradients are where the 9-color system shows off. Then peel a UV DTF sticker onto a mug, tumbler or phone case: no heat press needed, waterproof, with a glossy raised 3D texture.
It's free — you only cover shipping. Apply code BEARSAMPLE at checkout for 100% off the pack price. No upload, no setup, no minimums. Compare us with your current supplier and decide with your own hands.
Ready to go bigger? Build a custom DTF gang sheet, try HyperColor for color-critical work, or order UV DTF stickers by the sheet.
What printers say
Write a review
DTF Application & Care Guide
Use these professional settings for the best results. Always run a small test first, as presses may vary.
General Application Settings
- Temperature: 290–320°F
- Time: 8–15 sec
- Pressure: Medium (35–45 psi / 3–4 bar)
- Peel: Hot peel – remove film immediately while warm
Fabric-Specific Recommendations
| Fabric | Temp (°F) | Time (sec) | Notes |
|---|---|---|---|
| Cotton | 310–320 | 12–15 | Durable, best wash resistance |
| Polyester | 285–300 | 8–10 | Lower heat to avoid scorching |
| Cotton/Poly Blends | 300–310 | 10–12 | Helps reduce dye migration |
| Spandex / Lycra | 285–295 | 8–10 | Do not overstretch fabric |
| Denim | 320 | 15–20 | Use firm pressure |
| Fleece / Wool | 300 | 12–15 | Pre-press to flatten |
| Leather / PU | 275–285 | 6–8 | Test first, low heat only |
Product-Based Guidelines
- T-Shirts & Hoodies: 310°F / 12 sec
- Caps: 290°F / 12 sec
- Tote Bags: 310°F / 10 sec, firm pressure
- Jackets (Poly/Nylon): 290°F / 8 sec, protective sheet
- Sports Jerseys: 285–300°F / 8–10 sec, plus 2–3 sec finish press
Extra Tips
- Pre-press garment 2–3 sec to remove wrinkles & moisture
- Always use parchment or Teflon sheet
DTF Transfer Care Instructions
- Wash inside out at 30 °C (86 °F)
- Do not bleach, tumble dry, or iron directly on the design
- Wait 24 h before first wash
UV DTF Application & Care Guide
Use these tips for perfect UV DTF results. Surfaces may vary — always test first.
General Application Steps
- Make sure the surface is clean & dry (no dust or oil).
- Cut your design, peel the backing film.
- Place the decal, rub firmly with a squeegee or card.
- Slowly remove the carrier at 180°.
- No heat press needed.
Recommended Surfaces
| Surface | Tip | Extra Notes |
|---|---|---|
| Glass / Mirror | Stick, rub, peel | Degrease first |
| Metal (bottles, tumblers) | Rub firmly | Best on smooth coating |
| Plastic / Acrylic | Gentle pressure | Avoid textured plastic |
| Laptop / Electronics | Press edges well | Only non-porous areas |
| Ceramic / Mug | Stick & rub | Hand wash preferred |
| Wood (smooth) | Seal first | Needed if porous |
Product-Based Guidelines
- Tumblers & Bottles: Press edges firmly for 10s
- Laptop Covers: Smooth from center outwards
- Glass Jars: Clean with alcohol before applying
- Ceramic Cups: Hand wash only, don't soak
Extra Tips
- Keep carrier film flat, don't fold.
- Avoid applying on hot or wet surfaces.
- For outdoor use, add clear coat for durability.
UV DTF Care Instructions
- Hand wash or wipe with mild soap.
- Avoid dishwasher & abrasive sponges.
- Keep away from extreme heat.
